Skip to content

24/7 Emergency Service

(405) 500-5333
← Back to Answer Hub
Electrical

Why Does My Electric Furnace or Heat Pump Keep Tripping the Breaker?

Your heat kicks on, runs for a bit, and the breaker snaps off — or it trips the moment the emergency-heat strips engage on a cold morning. Here's what's actually tripping, why it shows up in winter, and when it's an electrical fault instead of an HVAC one.
G Graco November 12, 2026
6 min read

It usually happens on the first genuinely cold morning of the season. The thermostat calls for heat, the system runs for a few minutes, and then — click — part of the house goes quiet and cold. You find the tripped breaker in the panel, flip it back, and it holds for a while before doing it again. Or it trips the instant the heat comes on, before the house ever warms up.

Across the OKC metro, this is one of the first electrical calls we start getting every November, right as people switch their systems over from cooling to heating for the first time in months. The good news is that a breaker tripping on your electric heat is rarely random, and the pattern of when it trips tells you a lot about what’s wrong. Here’s how to read it.

Electric heat is a genuinely big electrical load

The reason this problem shows up on heating systems far more than cooling ones comes down to simple physics. Making heat with electricity takes an enormous amount of current. A bank of electric resistance heat strips — the kind inside an electric furnace, or the backup “auxiliary” and “emergency” heat on a heat pump — can draw 40, 60, or even 80 amps when it’s fully energized. That’s a massive, sustained pull, often several times what your air conditioner asks for in the summer.

A circuit, breaker, and set of wires that carried that load fine for years can start to fail at exactly the point of highest demand. Metal expands when it heats; a connection that’s slightly loose makes resistance, resistance makes heat, and heat makes the connection looser still. So the trip tends to arrive right when the system is working hardest — which, for electric heat, is the coldest part of the coldest morning.

Read the pattern: when does it trip?

Pay attention to the timing, because it narrows things down fast:

  • It trips only when the backup/emergency heat engages (heat pumps). On a milder day your heat pump hums along on the compressor alone and never trips. Then a cold snap hits, the aux-heat light comes on, and the breaker goes. That points squarely at the electric heat-strip circuit — the strips, their breaker, or the wiring feeding them.
  • It trips the moment any heat is called for (electric furnace). If you have a straight electric furnace and it trips almost immediately on startup, the problem is usually in that heavy heat-strip circuit itself, or in a shorted element or failed sequencer that dumps too much load on at once.
  • It trips after running a while, not right away. A circuit that holds for ten or twenty minutes and then trips is often a thermal problem — a breaker that’s weakened with age, or a loose connection heating up until it finally lets go. This is one of the more common patterns we see on older panels.
  • It trips instantly and hard, every time. An immediate, aggressive trip can mean a direct short or a ground fault — a heating element that’s broken down internally, or damaged wiring. That’s the one to stop messing with and get looked at.

What you can safely check yourself

There’s a short list of things worth ruling out before you call anyone:

  1. Check the thermostat mode. If you’ve bumped it to “Em Heat” (emergency heat), you’ve told a heat pump to run on its electric strips only, skipping the efficient compressor entirely. That dramatically raises the electrical load and can trip a marginal circuit. Unless a tech told you to run emergency heat, keep it on plain “Heat.”
  2. Change the air filter. This sounds unrelated, but a clogged filter chokes airflow across the heat strips and the furnace. Less airflow means heat builds up, which can trip high-limit safeties and make the whole system labor — and a laboring system draws more current. A fresh filter is the cheapest thing you can try.
  3. Look — carefully — at the breaker and panel. With the heat off, is the breaker for the heat/air handler warm to the touch when others are cool? Any brown scorching, a burnt smell, or a buzzing sound at the panel? You don’t need to touch anything inside; just note what you see and smell. Those signs mean stop and call.
  4. Note exactly when it trips and how long the system ran first. That timeline is the single most useful thing you can hand a technician.

What you should not do is keep resetting it, and you should never swap in a bigger breaker to “make it stop.” That breaker is sized to protect the wire behind it; a larger one just lets the wire overheat silently, and that’s how a nuisance turns into a fire.

When it’s an electrical problem — and when it’s the HVAC

This is the part that frustrates homeowners, because electric heat sits right on the line between two trades. Sometimes the breaker is tripping because the equipment is faulty — a shorted heat-strip element, a stuck sequencer energizing everything at once, a failing blower motor. Those are HVAC repairs. Other times the equipment is fine and the electrical system is the weak link — an undersized or aged breaker that can no longer carry its rated load, a loose lug on the heat-strip circuit, corroded or overheated wiring, or a panel that’s simply tired.

A few signs tip it toward the electrical side specifically: the breaker or its wiring runs hot even when the load is within spec, you see discoloration or feel heat at the panel, the same circuit has been a repeat offender for a couple of winters, or your panel is an older or recalled type that’s known for weak breakers. In Oklahoma’s older housing stock we still find plenty of panels that were never really sized for the all-electric heating loads later added to them. Diagnosing whether the breaker, the circuit, or the panel itself is the real bottleneck is exactly the kind of thing our electrical panel and breaker specialists sort out — and if the fault turns out to be in the heat strips or controls instead, we can take care of that side too.

The bottom line

A breaker that keeps tripping on your electric furnace or heat pump is almost always reacting to the enormous current that electric heat demands, and when it trips is your best clue: only on the coldest mornings when the backup strips kick in points at the heat-strip circuit; a trip that builds over several minutes suggests a weak breaker or a loose, overheating connection; and an instant, hard trip hints at a short or ground fault. Check the thermostat mode and the filter, look for heat or scorching at the panel, and note the timing — but don’t ride the reset button, and never oversize the breaker. The whole point of that breaker is to cut power before a straining circuit becomes a fire.

If your heat keeps knocking out a breaker anywhere in Edmond, Oklahoma City, or the surrounding metro, Graco will trace it to the real cause — breaker, circuit, panel, or the heating equipment itself — and fix it right, with flat-rate pricing you approve up front before any work begins. Call us at (405) 500-5333.

Frequently asked questions

Why does my heat pump only trip the breaker when it's really cold out?
Because that's when your backup electric heat strips switch on. A heat pump by itself is a modest electrical load, but when the temperature drops the system calls on its auxiliary or 'emergency' heat — a bank of electric resistance elements that can pull 40, 60, even 80 amps. If that circuit, its breaker, or the wiring is marginal, the strips are what pushes it over the edge. A trip that only happens on the coldest mornings, right when the aux-heat light comes on, points straight at the heat strips.
Is it safe to keep resetting the breaker on my electric heat?
Once, to see if it was a fluke, is reasonable. Repeatedly, no. A breaker that keeps tripping on the same heating circuit is doing its job — it's telling you that circuit is drawing more current than it's rated to carry safely, or that something has faulted to ground. Forcing it back on again and again lets the wiring, lugs, and connections keep heating up, which is exactly how an electrical fire starts. If it trips more than once, shut the heat off at the thermostat and get it diagnosed.
How do I know if it's the furnace or the electrical system?
A rough rule: if the equipment runs fine on a smaller load and only trips when the big electric heat engages, or if the breaker itself feels hot or looks scorched, the electrical side needs a look. If the system short-cycles, smells hot, or won't heat at all regardless of the breaker, the HVAC equipment is likely the culprit. In practice the two trades overlap here, so the honest answer is often that you want whoever shows up to check both — the circuit and breaker as well as the heat strips and controls.

Found this helpful? Share it.

Send it to a neighbor, or save it for later.

Follow Graco on Facebook and Instagram for seasonal home tips and local project photos.

Have a question we didn't cover?

Guaranteed reliable service or your money back.

Call (405) 500-5333

Contact us today

24/7 Emergency Service

5% OFF

Military · First Responder · Educator

Plus seasonal tune-up specials and new-system credits.

📞 Call Now (405) 500-5333 View All Promotions →

24/7 Emergency Service

Need it fixed today? We answer 24/7.

Guaranteed reliable service or your money back.

Call Now Book Online